0 DEFAULT SETUP LCD TV

By Unknown | At 11:27 PM | Label : DEFAULT SETUP LCD TV | 0 Comments

BRAND MODEL FOR chassis SPESIPIKASI
REMOVING PROTECT MODE
FACTS
LG
SHARP UNIVERSE GA IC TDA 9381/IX33xx
REMOVE JUMPER JA 223
SHARP X-Presion IC M6126XX REMOVE
JUMPER JA
STV POLYTRON EXCEL IC 2238H (SMD)
Removing Jumper (J345),
FOR MELEPSAKAN OF BCL
STV POLYTRON 2286H IC DIODE REMOVE
D 304
TO REMOVE FROM BCL
POLYTRON HBM 00-XX IC 16 PIN POSITION MUST
HIGH
PROTECTION FOR VERTICAL (DETECTION AC 50 Hz)
SANYO
PANASONIK
SONY
Related Posts
Newer Posts Older PostsHome
WELCOME
Labels
Monitor Menu Service
Benq LCD Monitor
Press and hold the "Menu" and "Exit" then
press the "Power"
Once lit LCD press the "i".
The second way press "Power", "Select" and "
Menu "together after lit LCD
press the "V".
Dell LCD Monitor
Press and hold "Auto" and "+" or "Enter"
and "+", then the "Power"
Once lit LCD press "Menu" then
select Factory.
LG LCD Monitor
Press and hold the "Menu" and then press
"Power" after flaming press "Menu"
Viewsonic LCD Monitor
Press and hold the "2" then "Power",
after the yellow LED
press the "1" keudian select "Factory menu"
Proview LCD Monitor
Turn on the LCD and then press and hold "" then "Power".
Viewsonic CRT Monitor
Before the monitor is turned on press and hold the "1"
and "2" then "Power"
after 5 seconds "1" and "2" is released later
again press "1".
Provision CRT Monitor
Press and hold the Menu and then plug
AC power, the monitor turns
remove the menu.
TV Menu Service
AIWA
Disassemble the original remote, press the blank
on the VolUp.
AKARI
Press and hold the Sleep in remot >> press Menu in
panel TV.
AKIRA
Press the AV button on the remote >> press Menu >>
press QuickView >> press Mute. Moving menu
with a timer, change the value to VolUp /
VolDown.
Akira LC863324A LA76810
Press "PROG" followed dg pd remote press 6483,
repeat for setting "white balance, factory
modes, get out.
Akira TMPA8803/21/23
Press vol-on the tv and remote pd disply
coincide
Akira LC863320A, LC863324
Press menu 2X pd remote and press "Q
view or Return "and the mute button remote pd
alternately. Press the timer button to select
service acces item. To exit the menu press pd
remote.
Akira STV2248, STV2195, STV2185
Press menu, AV, "anal" remote pd. Press PP or
ST-by to come out.
Akira TDA935X/6X/6X
Set tv pd position 0, press and hold the mute pd
remote and press menu to appear "S"
pd screen tv.
Akira TB1238AN
Set minimum vol tv and press mute pd
remote until the "D". press menu to
select service acces item. to exit press
power.
Akira TB1238
Set pd tv ch 12, then ch38, press "menu"
For calling "post.lock", press mute.
Enter the password is 1238, then the tv will
displays "M".
CRYSTAL
TV is in standby mode, press VolUp arrested >>
press VolDown, both detained for TV
live alone.
GOLDSTAR
Taken together VolUp press Menu + +
VolDown ChDown + TV panels.
HITACHI
hitachi / hitachi_fujian: Turn off the tv with the
power panel, press the AV button on the panel on hold
>> Turn on the TV with the power button on the TV,
AV button is still on hold until the tv turns
itself.
JVC
Press OSD / Display arrested >> press Picture
(VSM standard).
alternatif1: Press OSD / Display / Info arrested >>
press Mute.
alternatif2: Press OSD / Display / Info arrested >>
press Cinema / Game.
LG
FLATRON: Press OK on the remote being held >> press OK
in panel TVs, both arrested about 5 seconds.
Alternative: Press Menu on the remote, press the menu
diremot again arrested >> press Menu on the TV panel,
both arrested about 5 seconds.
BRAND CHINA
alternatif_1: Position volume on 0/minimal >>
press the Display >> press VolDown on TV panel
detained >> press Display again.
alternatif_2: Press Menu on the remote >> press Menu
on the remote again >> Display >> tap tap Mute.
LA863328A-5028/2MD0, LC863320A-C81DC =
Find a blank button in the remote when not in use.
Choosing the CHUP / ChDown, adjust VolUp /
VolDown.
LC863324A-5T51, M37220M3-167SP,
LC8633528B-50S8 = Go to menu
AutoProgram / autosearch, and then press
6483 respectively to enter the service menu.
Press sequential 6483 again to get into the
factory mode.
87CK38N-1H74 + TB1238 = Reduce the volume
to 0, press Vol-paneled, hold press OSD /
diremot display to enter the mode S. Repeat
steps to get into the mode D. press
Power (remote) to save / exit.
LC863532A-5Z00 + LA76810 = Decrease the volume
to 0, press Vol-paneled, hold press OSD /
diremot display to enter the mode S. press
Power (remote) to save / exit.
M37220M3-010SP + M52340SP = Press Menu
paneled, hold, press the sequence 6483. CHUP /
Down select menu, VolUp / Down adjust the data,
power (remote) save / exit.
LC863528B-51C3 = Press Display, press the Mute 3
times. Move the page to Sleep. CHUP / Down
select menu. VolUp / Down adjust the data. Press
Menu to save / exit.
M37160M8 M61266-058FP + (SMD) = Press
Menu, press the sequence 6483. Move page
by Mute. CHUP / Down select menu. VolUp /
Down adjust the data. Press the Power / Standby for
save / exit.
M37160M8-073FP (SMD) = Press the Mute, press PP.
press (_ / __) to move the page, press the TV
to exit.
LC863328A-5Y29, 5Y28, 5Y19 = Volume position 0,
press Vol-resistant, press 0 diremot 3 times.
LC863528B-52K7 = Volume position 0, press the menu
5 times (go to channel edit menu), select
EXCHANGE PROGRAM, enter 2483. Move
use QuickView page.
LC863532B-52H8 + LA76810 = Press Menu,
press row 888.
LC863532B-55L1 (WCOM) = Volume position 0,
press menu, press the sequence 6568. Move
Display page wear.
M37160M8 M61266-058FP + = Press Menu,
press sequence 6483.
TH-50J2-3RR0 = Set volume / balance up to
RS03, press Menu, press Mute.
alternatif_3: Press Menu on the remote >> press Menu
on the remote again >> press QuickView >> press Mute.
NIKO
Posisisikan volume 0/minimal >> press
VolDown in panel TVs arrested >> press Display.
PANASONIC
TX series: Put the volume at minimum position,
put sleep at 30 minutes >> Press the display
detained >> press VolDown on the panel. Exit
Normal service menu press on the remote.
alternatif1: Put volume at minimum position,
put sleep at 30 minutes >> Press Display >>
press the display again >> press VolDown detained in
panel. Normal Press on the remote to exit
service mode. buttons 1 and 2 select the page /
group setting, 3 and 4 select an item, VolUp /
Down to change the value.
alternatif2: Short / konekkan momentary pin FA1 to FA2
or TP8 to ground.
PHILIPS
Press VolUp arrested >> press ChDown. Exit
the Standby / Power.
Alternative: TV is in standby mode, press the
sequence 0 >> 6 >> 2 >> 5 >> 9 >> Menu in
remote.
POLYTRON / DIGITEC
TV in standby mode, press Menu on the remote
hold until the password prompt appears,
to go into service mode enter 1013, for
factory fill mode 1014. Saving with
the Menu button on the remote.
RCA / SABA / THOMSON
Tv is off, Press the VT (blue button)
diremot arrested >> turn on the tv to use the
power panel.
notes:
for some models, press the button once VT
again.
SAMSUNG
zoom_vision: TV standby, press
sequence in the remote, P.STD >> Help >> Sleep
>> Power.
plano: TV standby, press sequentially in
remote, Display >> Menu >> Mute >> Power.
alternatif_1: TV standby, press sequentially
in remote, Menu >> P.STD >> Mute >> Power.
alternatif_2: TV standby, press sequentially
in remote, Mute >> 1 >> 8 >> 2 >> Power.
SANYO
Alternative: Press Menu diremote arrested >> press
VolUp panel TV.
dynamic: Press Menu on the TV panel, on hold, press
number 1 diremot (thx. Aisy).
SHARP
expression: Connect two jumper near
tuner (pcb jumper holed below).
wonder_universe: Connect just two
jumper (J122 - J124).
Alternative: Turn off the TV to use the panel, press
together VolDown + CHUP on the panel,
while detained turn on the TV to use the power button
panel.
SONY
Turn off the TV with the remote, press the sequence in
remote, OSD / Display >> 5 >> VolDown >>
Power.
Alternative: Turn off the TV with tv panel, press
VolUp together with Chup, turn
TV panel with button, hold it up to light up.
TCL
Press Display diremot arrested >> press
VolDown on TV, they arrested approximately 3
second.
TOSHIBA
Press Mute diremot, screen mute sign appears,
press Mute again detained >> press Menu on TV
KONKA
K2100cx, k2139ax, 2166axt, 1438axt:
1.Press menu 1x diremot
2.Press recall 3x diremot
if it is locked press press mute and Angaka 9
3x as much
k2139c3, 5139c3:
1.kupas skin left under the remote and press
with a screwdriver until the
on fac mode to enter the menu press 4
and 8 buttons for setting press 1,2,3 and 4
3.Untuk k2588t models and 1488t press the 6
and 8 buttons on the remote, but the remote was jka
no tv's 2000s output rekan2
can use a universal remote brands cunghop entry
setting mode is used when the remote
function, directly press the sleep button it will
direct entry mode service
GOLDSTAR
Taken together VolUp press Menu + +
VolDown ChDown + TV panels.
CHANGHONG
turn down the TV volume to a minmum or nol.Tekan
MUTE button
on the remote and hold, press MENU on the tv.
will arise logo setting (S).
SAMSUNG
Standby press on the remote: MENU - PTSD -
MUTE - POWER ON
SAMSUNG PLANO osisi standby, press on
Remote: DISPLAY-MENU-MUTE-POWER ON
SAMSUNG PLANO DIGITAL HD100:
STANDBY-DISPLAY-MENU-MUTE-POWER
OR: STANDBY-MUTE-1-8-2-POWER ON
NOTE SMALL
AIWA A14-S1
BRIGHT AND DARK PICTURE THOUGH
CONTRAST was raised, NOT JUST STAY
KONTRAS.GANTI R614 R ABL: 150K
AIWA C20 KER
PICTURE ONLY raster or IF
NO, JUST A SHORT AND DIRECT
LOST. COLOR OR BLACK ONLY
IF PUTIH.GANTI AFT: 656
SHARP C14JO
SMALL IMAGES only inches
Amid SAJA.RASTER JUST EMPTY /
BINTIK.KESALAHAN HAPPENED ON TRACK
12V.GANTI Q604 FOR ration 12Volt D
ALSO GO TO TUNER.
SHARP EXPRESSION 51X220
Shown WITHOUT IMAGES BY POSITION
HIDUP.KADANG VOTE BACK TO STANDBY
(Protek). REPLACE R limiters for 180V
R621: 1 OHM
WONDER SHARP 14 ".
VERTICAL IC OFTEN THEN BURNED TO PARTICIPATE
Scorched TWO RESISTOR IE: R503
EXACTLY UNDER THE REFRIGERATOR (heatsink) IC
VALUE 220 OHM AND ANOTHER ONE BEFORE
VERT IC (508) VALUE: 1.5 OHM
SANSUI SV-2050J
PICTURE LOOKS AND VIBRATING IN FILCKER
Accompanied THICK COLORED LINES
GELAP.GANTI c 708: 220/50V, C 517 AND 518:
100/160V.JIKA WITH SUCH flashes -
Flashing lights LITTLE OF THE TO
DOWN, GANTIGANTI CF902: 503 atao 500
SANYO CAP3002
MATI.DENGAN TR.HOR SHORT CONDITION. IF
TR.REG REPLACED HIS, B + VOLTAGE risen
LEBIH.KERUSAKAN 200V UP TO R555
SECTION 47KOHM optocoupler
SANYO CG21 XS2
TV LOCKED IN POSITION STANDBY.POWER
WANT TO START BUT BACK PROTEK.PUTUSKAN
J830 JUMPER OR CHANGE FBT.
DIGITEC DM172021
SAT PROGRAM CAN NOT SAVE IN
SEARCH IN SPITE OF TRANSFORMER AFT (9074) AND VIF
(9073) ZENER D712 BAGUS.GANTI NEAR 5VOLT
IC MEMORY MN12C201D
BLACK BEAUTY DIGITEC BB2071
115V 300V VOLTAGE AND THERE, FBT START
ONLY HEARTBEAT, TEG 12V TO IC OSC.HOR
ADA. TV EQUIPMENT NOT START.GANTIC76: 180N
IN REGULATOR
DIGITEC / POLYTRON DM 143 031
LATE TO START, accompanied IMAGES IN D
FLASH AND WELL sway
MENYEMPINYA WIDE GAMBAR.GANTI
C518: 100/35V. c514: 330/35V.
C515: 680/560pF. R511: 5KOHM / 1%. R517:
15KOHM / 1%
DIGITEC DM143031A
First turned PICTURE LOOK
POLOS.DENGAN ALL WHITE BUTTON PANEL
NOT FOR VOLTAGE BERFUNGSI.TERUKUR
JUST 22V 12V 12V AND VOLTAGE
MEASURABLE 10VOLT.GANTI ONLY R557: 330
OHM / 1 WATT
POLYTRON / DIGITEC BlackBox SERIES
VERTICAL LINE ONLY TV BERDIRI.DENGAN
CONDITION OF THE HORIZONTAL COMPONENT; C
2.2 / 160V AND R 3K9/2W PUTUS.GANTI C 390
ATAU470n/250V
POLYTRON Grandmaster GM 1481
SYNC IMAGES AND DO NOT LOOK LOGO
LOOK OF TV STATION IN CENTRAL-
CENTRAL LIMIT IN THE THICK BLACK LINE
BAWAH.GANTI R452: 50KOHM 1/8 WATT
POLYTRON / DIGITEC
USING IC TDA 8360/61.KERUSAKAN
Horizontal HORIZONTAL LINE ONLY
SAJA.MESKI IC vertical NORMAL.GANTI R
401: 2M2 OHM
Minimax POLYTRON SERIES MX1452G
TV JUST WANT TO START AND SOMETIMES SOMETIMES
HARD TO MENYALA.GANTI C507: 10/50
WITH 47/100V
SOLITRON SM37-98
POWER SUPPLY NOT ONLY 45 + START.B
VOLT.GANTI D81: ZENER 4V7
FTC FUJITEC 1459
PICTURE / Raster narrowed at LEFT AND
KANAN.WARNA BE BLACK PUTIH.TERJADI
DROP IN VOLTAGE B +. GANTIC 517: 33/160V
JVC AV-K SERIES KT21T2
Raster CONTAINED UPPER LINES
WHITE blanking thick 2 CM.GANTI C
428: 100UF/50V.
JVC C 20 RNs
TV STAND POSITION BACK OFTEN BY.MESKI
POWER BUTTON AND PROGRAMS ON TV IN
Click on TV STILL CAN NOT START.GANTI
R751: 100KOHM
AKARI 20M88R
Raster enlarge and shrink TAK
KARUAN.GANTI REGULATOR D809 IN4148
AKARI CTV14
VOTE NO, WORK IC ZILOG NORMAL.IC
TA 8690AN BAGUS.GANTI Q06: C3289.
AKARI14-20
TRANSISTOR REGULATOR (D1710) ALWAYS
DROP WHEN NEW IN CHANGE without a chance
MENYALA.KERUSAKAN HAPPEN TO SECTION
Fedback R810 optocoupler IE: 47KOHM
THE VALUE enlarged.
IF THE IMAGE IS NOT STABLE OFTEN ARISE
OSC LINES LIKE NO HOR
TEPAT.GANTI C HORIZONTAL DRIVER
10uF/100V
Jhonson CTV147
IMAGES DEFECTS IN THE VERTICAL accompanied
Blanking LINES IN 3/4 SECTION
IF IN VOLUME ATAS.DAN
Exaggerated, PICTURE LOOKS MORE SEVERE
TAK sway STABIL.GANTI C119: 470/50V
SONY KV20XXX
IF POWER ON EMPTY PICTURE
Raster ONLY DIRECT AND VOTE
FULL.GANTI R627: 4.7 OHM FOR SUPPLY
5.5 V
SAMSUNG CS 5085
BOTTOM VERTICAL PICTURE LESS
WITH WITH NO LINES
MENENTU.SERTA ARISING screeching noise
AT STANDBY. CHANGE C407: 330/50V
GOLDSOUND PANASONIC TC-SERIES
Horizontal VERTICAL LINE DRAWING ONLY
IF CONDITION LIGHT / NORMAL NORMAL.TAPI
IF CONDITIONS IN BRIGHT Dim. CHANGE R
525: 120K / 470K
SoundMAX GOLDSTAR
TV STANDBY POSITION WITH LED LIGHTS
FLASH-KEDIP.GANTI DIODE RU2K NEAR
6707 STR WITH ANYWAY C D IN4007.GANTI
330ATAU470/35.
GOLDSTAR / LG
TV OFTEN TO POSITION ITSELF OFF
STANDBY, REMOTE POWER IF IN Turn on
TV BACK TO BACK OFF HIDUP.TAPI
After so HOURS TO POSITION
ELCO STANDBY.GANTI DRIVER HOR 10UF/100V
CRYSTAL
TV JUST KNOW WITHOUT STANDBY
CAUSED. USE REMOTE, PRESS
POWER BUTTON ON THE REMOTE AND BUTTON
OK TOGETHER AND HOLD TO TV
CAN START BY ITSELF.
PHILLIPS GR1225
TV LATE TO VOTE START.TERDENGAR
Wheezing ARISING IN FBT.KEMUDIAN
PICTURE LOOKS IN THE DARK WITH accompanied
LINES overtaken HORISONTAL.DI
THEN VOTE D Lately
MUNCUL.ganti c5524: 82n/100V AND
C254: 220uF/35V
SHARP 21 BN1
PICTURE LOOK LESS KONTRAS.DI
Accompanied colors LOOK
SMEARING.KERUSAKAN HAPPENED ON TRACK
9v THE ONLY MEASURABLE 6v.GANTI
Q605 882 REGULATOR FROM 16V TO 9
VOLT.DARI PIN 7 FEET FBT
FUJI ELECTRIC FCH-2100
GRAPHICS AND SOUND LIKE A VERY WEAK
NO USE SEARCH ANTENNA.AUTO
DOES NOT WORK, NOT TOO FINE TUNING
BERPENGARUH.WARNA PERMANENT BLACK
PUTIH.GANTI X-TAL 4.43
INDOTECH 20 "
AT THE FIRST PICTURE lit
Shortly LIGHT AND DIRECT
NO CONTRAST GELAP.PENGATURAN
BERFUNGSI.KERUSAKAN HAPPEN TO SECTION
ABL R314: 12OKOHM
SANTEC C1428
TV STANDBY POSITION AND BUTTON PANEL
NO REMOTE BERFUNGSI.GANTI X-TAL
PROGRAM: 10M (10,000)
Sanken ST BAZZONEYE 2181
TV AND ONLY POSITION STANDBY.REMOTE
PANEL BUTTONS NOT BERFUNGSI.TEGANGAN
FOR 24 V AND 12V DROP.GANTI C
541: 100/35 AND C 553: 470/16V
Changhong 21B18EA-TB1238AN
OSD lost, damaged or slightly short c in T
OSD oscillator, the solution: open pin oscillator OSD T
in gnd.
Konka K2139C3-TB1238AN
Disearching through, difine OK but too long
mbleset, change in T c VCO (pin50 & 51 IC
TB1238AN) dg c ceramic 22pF.
POLYTRON DIVA
HBT program IC-00-02G
On a short (logo appears) then st-by, the damage:
Protec. Protec pin layout HBT IC 62-00-02G, TEG
Protec pd only about 2v, normal conditions
should be around 5v. Replace 1mf/50v dr c402 pin 3
An IC 5522 vertical.
Digitec DM142021, MN152451FEL:
Vt-voltage do not want roads, damaged R734 33k.
-Contras are not functioning, broken R345 220K, R436 10k
(From abl).
Digitec TDA8361:
-The first time on a normal picture, then
trus shrunk image left and right horizontal line
less, less 8v voltage, check circuit
supplynya.
-Picture sometimes not catch the broadcast
(TEG AGC 0), vertical fold lower, long-
Sometimes the old normal, C202 22nf rather short (pin
52 IC TDA8361).
Digitec super ninja:
Color is gone, there TA8690AN IC pin21 r10k trus
diseri with r10k to gnd, gnd r10k which to replace
the 5k.
Digitec 143031B
-Did not catch the broadcast, Tr303, Tr309
OSD-no, Tr712.
Digitec DN1411M:
Normal picture no sound (crackle-crackle)
but sometimes the sound normal, damaged ZD 8v on
STV2286 IC pin55.
Digitec HBM-00-02:
No pictures, just no line direction
horizontal at the bottom of the screen, IC program
damaged.
Digitec ichiban DC1402K:
-Images like AGC is too big.
-Disearching pass.
AV-in ok.
Damaged c133 2.2 / 50V, pd pin53ic TDA8841, AGC.
Detron 2065 models:
Horizontal Tr often broken, replace c462 6.6 nf (pd
colektor tr h).
Can not get off on, check Q506, Q505, Q507.
Goldstar
No sound, disearching through, broken tr ID,
located next to the ic memory.
No colors, AV nor color, damaged
c534 (the physical form as r10k).
There are no images and sound, normal OSD, audio
out there, there's no video out, Q202 is broken, (dr pin43
ic TA8690AN, PIF).
There are no images (plain) normal voice, short c501
(Pin 54 IC TA8690AN).
Panaconic
> Output voltage regulator over.
If this is not addressed will result in
damages are more fatal. Damage
can we know the early symptoms
as follows;
- When you first turn on the tv is not immediately
catch the broadcast, only after some time
Normal. This is due to less stable
supply voltage for VT tuner due overnya
regulator output voltage when the first
turned on.
- Shortnya ZD on TEG Supply for VT tuner,
if this happens then when we onkan tv tv not
want to live and there was a "ngiiik".
To overcome this problem we regulator over
should replace all the values ​​elco 47
microstructures on regulator circuit. If elco has
we replace a fixed voltage over it, check
resistor826 whose value is 22ohm, usually
broken.
> Relay sound "ceklek-ceklek", the tv did not want on.
Damage is common in the value of R803
470K.
> Disearching through, difine-tuning can. Check TEG
AFT out the 30 pin IC AN5192K, if there is no
voltage, usually ZDnya short.
> If exposed to a bright picture (too much contrast)
tv off, the red LED life. R525 broken, its value
22k.
> Normal Picture no sound, audio IC
Normal. This often happens. diode breakdown
next audio IC, PCB edge is located, replace
by D 4007.
> To enter service mode to menu: press the V-
Disply on tv and on the remote to exit
press "N" (normal) on the remote.
Changhong 21E68
Drawing nearly half of the top lines
(Such as B + ic less vertical). ic vertical wear
LA78040.
Damage to R614 56k, stretchy value.
PROTECTION
PANASONIC
TNP4G007BD, MN152810TT, AN5606K, LA7837
Protection 1: IC601 Pin20, X-ray protector,
normal 0V, R428 (56K) vertical output sensor,
D522 sensor heater / x-ray, Q503 sensor ABL/X-
ray, secondary sensor Q451 TFB / X-ray.
Protection 2: Q1136 video synchronization detector
from pin12 pin50 IC601 toward IC 1102
(MN1528110TT).
GOLD SERRIES, MN1528111, AN5192K-A, LA7837
Protection 3: IC601 pin55, X-ray protector,
0V normal, vertical sensor output R426, Q451
(A1015) sensor voltage 24V and 12V.
SHARP
DUNTKD746WE, 14E25, IXB855WJZZ,
BSC25-2631S/FA122WJ-B, WA216WJZZ,
LA78040N, STR-W5453A, AN17823A
Protection 1: Pin7 IC801, AC-detector, the value
depending on the setting of normal 3V + or 0V, default
3V +, D1002 15V zener 12V of output secondary
SMPS.
Protection 2: IC801 Pin63, protectionism main, normal
3V +, D1005 sensor 16V, 5V sensor D204, D203
sensor 33V, 180V sensor D605, D608 sensor X-
ray / Abl, Q603 sensor heater / X-ray.
DUNTKE134WE, 14R20D2, IXC245WJN4Q,
BSC25-0216F/FA135WJZZ, WA216WJZZ,
STV9302B, STR-W5453A, LA42031
Protection 1: IC801 pin64, AC-detector, the value
depending on the setting of normal 3V + or 0V, default
3V +, D1002 15V zener 12V of output secondary
SMPS.
Protection 2: IC801 Pin63, protectionism main, normal
3V +, 5VA sensor D1008, D1005 sensor 5VB,
D203 sensor 30V, 180V sensor D605, D604
sensor heater / X-ray, ABL sensor D608, Q603
sensor heater / X-ray.
Variants: 21EF250MK2
DUNTKC911WE, 51WF200, IX1226WJ, M61260,
FA0132WJ, WA165WJ, AN15524, STR-W6753,
AN17823A
Protection 1: pin6 IC1001, AC-Detector, values
dependent normal setting (ADC), D1010 sensor
Secondary 16V SMPS.
Protection 2: pin7 IC1001, main protectionism, value
normal 4V6, D605 sensor 180V, D608, Q603
sensor heater / X-ray sensor 33V D203, D1091
9VB sensor.
DUNTK9988WE, 14GT15, 14GT20, IX3368CEN1,
TDA8357, Z0140PE, F0193PE, TDA7056A
Protection: pin8 IC801, protectionism main, normal
3V2, 8VB sensor D609, D606 sensor ABL / X-ray,
D614, Q603 sensor heater / X-ray, D613 sensor
180V, 5VB sensor D752, D504 sensor 16VB
audio, D502, D503 vertical sensor.