Tuesday, November 20, 2012

TYPES OF DAMAGES TV

Devices: TV
Brand: Sony
Model: Sony - STR Goldstar
Symptoms: More than 24 hours of STR broken
Cause: faulty setengat Optocoupler
Solution: Replace the optocoupler


Devices: TV
Brand: Sony
Model: Sony KVG14V1
Symptoms: Raster somewhat above the middle line
Cause: Diodes (-15V) is broken
Solution: Replace the diode


Devices: TV
Brand: Sony
Model: kv-2965
Symptoms: No picture, sound flyback.
Cause: Res. R704 470K G1 broken parts.
Solution: replace R704 470K 1/2W.


Devices: TV
Brand: Sony
Model: kv-2565
Symptoms: horizontal transistor is always broken in a matter of seconds.
Cause: x-tal oscillator 500KHz Horz damaged.
Solution: replace the xtal oscillator directly B500F2 OK.
Note: replace the oscillator according to type (yellow), never tried blue can not be used.



Devices: TV
Brand: Sony
Model: Sony KP-E53MN11
Symptom: Power exists, will not start
Cause: 12V regulator IC die
Solution: Replace the 12V regulator IC



Devices: TV
Brand: Sony
Model: KV-G14B1
Symptoms: THERE IS NO SOUND IMAGES
Cause: R SHORT
Solution: REPLACE RESISTOR R857 = 82K
Note: This TV program CXP85116B IC and IC TDA8366 chroma, STR s6707 and vertical IC LA7830.


Devices: TV
Brand: Sony
Model: long
Symptoms: blink flame tube
Cause: potensio broken ceramic hstat
Solution: potensio who is replaced on the lights on the board or someone tespen


Devices: TV
Brand: Sony
Model: 20 WEGA
Symptoms: no raster
Cause: r0, 01.sket crt
Solution: check TEG heater, sketch crt
Note: If there is no change TEG r crt socket and check if the problem replace aj bro


Devices: TV
Brand: Sony
Model: KV20XX
Symptoms: GBR NGK POWER ON THERE ONLY DIRECT VOTE raster gedhe
Cause: SUPLY 5.5 V LESS
Solution: CHANGE R627 = 4.7 OHM
Links to this post
Issue 27
Devices: TV
Brand: Sharp
Model: wonder
Symptoms: There rgb color line, n back stanby
Cause: r33ohm that the voltage fuse to ignite Vertical Ic
Solution: replace r33ohm, and Ic Vertical
Note: vertical ic replacement, if it r 33terasa hot sangt



Devices: TV
Brand: Sharp
Models: 20U200
Symptoms: Voice gresek-gresek, nice pictures, sound system locked on D / K and can not be replaced
Cause: change and adjust, eprom 24C08
Solution: replace and adjust, eprom 24C08


Devices: TV
Brand: Sharp
Model: 51R200
Symptoms: The star of life and death, led to red
Cause: R502 check for voltage Vertical Gati if necessary
Solution: check for voltage Vertical R502 Gati if necessary


Devices: TV
Brand: Sharp
Model: 14W25
Symptoms: tv live briefly kept standby.
Cause: ProTec of ABL
Solution: turns R604, 39K putus.ganti tv back to normal.



Devices: TV
Brand: Sharp
Model: 20x20
Symptoms: total dead, when the power button is pressed Him indicator lights red, then green, then went back to red
Cause: solder off.
Solution: re-solder, IC EEPROM should be reset IC, the way he was when the TV is off, Jumper J137 to J138. After that turn on the TV, while for IC EEPROM Let wiriting return to normal TV is on, then turn off the TV, then remove the jumper earlier.


Devices: TV
Brand: Sharp
Model: Q vision
Symptoms: hold a red light green protectionism
Cause: 180k resistor open
Solution: replace the 180k resistor near abl pathways


Devices: TV
Brand: Sharp
Model: Q vision
Symptoms: dark picture sound normal
Cause: 33k resistor open
Solution: replace the 33k resistor on track afc


Devices: TV
Brand: Sharp
Model: sharp universe
Symptoms: Normal picture briefly switching off life
Cause: capacitors 104 open
Solution: replace capacitor ic 104 near croma


Devices: TV
Brand: Sharp
Model: wonder
Symptoms: regulator 6654 kerja.strf not okay
Cause: r 680k/560k putuss
Solution: replace r TSB
Links to this post
Issue 26
Devices: TV
Brand: Sanyo
Model: model forget
Symptoms: tv when turned glowing red indicator blink blink wrote ter aka protectionism
Cause: apparently after dilhat ditelusurri kissed and touched only on the location of the damage to flyback terprotek
Solution: replace the flyback solosinya yes definitely jos




Devices: TV
Brand: Sanyo
Model: CG 21 XS 2
Symptoms: TV stand is locked in position by.kalau power in on.TV willing to live and die lagi.protec
Cause: eeprom if its OK, then the vertical IC OK.B + 5 volt OK.
Solution: J830 jemper off, or change it directly FBT.
Note: tgl.27 september 2010




Devices: TV
Brand: Sanyo
Model: Dinamic
Symptoms: Dead total
Cause: Power Transistor suply shot
Solution: Replace the transistor
Note: Change the type of bu. . .




Devices: TV
Brand: Sanyo
Model: N0 chassis AC6A1
Symptom: No sound volume max sdh, Nice pictures
Cause: IC 3701 LV1116 broken
Solution: Before replacing the ic try this alternative way, off his first ic, wash the feet of his lower leg ic wear cuter / fine sandpaper, then reinstall nya.kl ic voice ic still not out Change lv1116N,
Note: kl spertpat interchangeable hard in his search to SC, Bs jg look at his blog mas alextro service, http://alextro-service.blogspot.com/




Devices: TV
Brand: Sanyo
Model: CG14SP1N
Symptoms: Dead total
Cause: TR Horz koslet (B & E)
Solution: replace TR Horz




Devices: TV
Brand: Sanyo
Model: FLAT SLIM CG21XS2 21
Symptoms: VOTE nonexistent
Cause: MEMORY NOT WORK NORMALLY WHEN DATA settings OK
Solution: The data SETTING FIRST, CAN NEW NGK KLO GNTI IC MEMORY
Note: SANYO MODEL UMTK NATURAL SY OFTEN DAMAGED DATA / IC MEMORY




Devices: TV
Brand: Sanyo
Model: CG21XS2
Symptoms: always return to standby will continue when lit
Cause: flyback his tiny little problem .. internal capacitor capacity changes FBT
Solution: with a way to cut (break) .. J830 jumper that led pin 23 of IC LA76938 (pin is called: INT1/P.0) one pin to detect / control the horizontal section.




Devices: TV
Brand: Sanyo
Model: box silver
Symptoms: Protec dead, no sound briefly hold stenbay
Cause: flyback transformer leakage
Solution: replace the flyback transformer
Note: if they need to replace the flyback siz setting v and h siz




Devices: TV
Brand: Sanyo
Model: dynamic LA76818A
Symptoms: NGK NO SOUND MAX VOLUME already
Cause: CORRUPT DATA settings
Solution: OPEN DATA SEARCH S.STE CHANGE 0
Links to this post
Issue 25
Devices: TV
Brand: Samsung
Model: CS-14H4MJO-MONO
Symptoms: Matot
Cause: STR SHORT
Solution: The safest use of switching power supply module


Devices: TV
Brand: Samsung
Model: bio vision
Symptom: No sound only raster images white only
Cause: teggangan abl no
Solution: replace r abl value of around 120k + b keabl


Devices: TV
Brand: Samsung
Model: CB21MLH
Symptoms: The image moves down up
Cause: IC Memory
Solution: Replace the Memory IC 24c16


Devices: TV
Brand: Samsung
Model: 14 flat CTV
Symptoms: open 10 cm vertical striped folding and
Cause: broken vertical yoke parts
Solution: replace the yoke tv ok again


Devices: TV
Brand: Samsung
Model: CS-15K10ML
Symptoms: Matot, suply SOUND POWER ringing
Cause: TR HORIZONTAL SHORT, THERE ARE PENEBAB YOKE ANGUS,,,,,
Solution: TR CHANGE AND YOKE WITH NICE
Note: TR D2499/YOKE H OM VER 5.4 15 OHM



Devices: TV
Brand: Samsung
Model: CS-29M21MQUXXSE
Symptoms: Blanking
Cause: Micon on ngepong,
Solution: Solder again.!



Devices: TV
Brand: Samsung
Model: flat 17inci
Symptoms: horizontal off continues
Cause: yoke konslet
Solution: email lifting ll wipe lg dg dg thiner glue alteco 1/1
Note: buy overpriced yoke again



Devices: VCD
Brand: Samsung
Model: Z10Q
Symptom: No picture
Cause: Video output from puts zic3
Solution: Join / jumper with pins 13 pins 4 zic3
Note: Can jga len dpts and pindahkn pin 13 directly to pin 4 on zic3 (Winbond W99520P)



Devices: TV
Brand: Samsung
Model: 21 flat
Symptoms: The first normal picture, about two minutes blanking green,
Cause: RGB bag there is an abnormal voltage
Solution: tr bersihin RGB in, if there is to be replaced,,,,
Links to this post
Issue 24
Devices: TV
Brand: Polytron
Model: minimax
Symptoms: protect
Cause: protect vertical
Solution: replace c402


Devices: TV
Brand: Polytron
Model: minimax 21
Symptoms: Vertical menyempit.lebarnya sktr only be 10cm.
Cause: all of vertical normal stress components, resistors, ICs, capacitors all ok.
Solution: I replace the 1N4002 diodes deket vertical IC. (Forgot his no series D:?) Turns the diode check is not even in my locker right bocor.begitu nyuzz mak ...
Note: apparently visik observation, and multi meter we can still lying by komponen.sehingga should be a record for us the technicians to be more observant and careful. and the principle of change first


Devices: TV
Brand: Polytron
Model: DM-1485
Symptoms: Plain White Drawing Without OSD
Cause: The raster noise is not no snow
Solution: replace the transistor T311 = BC547


Devices: TV
Brand: Polytron
Model: ga
Symptoms: ganbar only vertical
Cause: terjdi sorting the capacitor
Solution: replace capacitor 364j/400v


Devices: TV
Brand: Polytron
Model: minimax
Symptoms: no broadcast
Cause: replace the tuner first checks
Solution: if replaced would also replace the tuner ngak HBT IC 00-02



Devices: TV
Brand: Polytron
Model: Polytron 123
Symptoms: The standby light on,,, kadang2 want to start
Cause: faulty capacitor
Solution: replace capacitor c507 with 10mf/100v
Note:


Devices: TV
Brand: Polytron
Model: minimax
Symptoms: start 5 seconds back stanbay
Cause: faulty capacitor 1 mf/50v
Solution: replace the vertical ic c402 in


Devices: TV
Brand: Polytron
Model: old model
Symptoms: totally dead.
Cause: Regulator not working
Solution: Usually Fet damaged.


Devices: TV
Brand: Polytron
Model: MX5203R
Symptoms: standby not want to star trus poer light flashes
Cause: B + voltage fluctuates
Solution: replace the diodes D505 & D507 at the B +
Links to this post
Issue 23
Devices: TV
Brand: Panasonic
Model: TC-20S11J
Symptoms: only standby button on the tv remote did not work despite of permanent standby
Cause: AC220 voltage is unstable
Solution: replace TR D1275A DRIVER horizontal or C1573
Note: Check all the voltages of the regulator should be stable. if oper. tr is always off


Devices: TV
Brand: Panasonic
Model: ts14s100
Symptoms: sound-Klek Klek
Cause: r470k pair drop
Solution: TEG b 90 drop hihg-low search r 470knya replaced aja,, check the other 47/50v elco
Note: regular tv mdel gini common


Devices: TV
Brand: Panasonic
Model: 21 top dome
Symptoms: picture looks dim.
Cause: r broken
Solution: replace the 137k resistor with a value of 525 ohms, the resistor in the ABL from B +.


Devices: TV
Brand: Panasonic
Model: TC-21GX20J
Symptoms: totally dead
Cause: transient voltage
Solution: replace the transistor horizontal


Devices: TV
Brand: Panasonic
Model: 21 inch
Symptoms: totally dead
Cause: damage ic eeprom
Solution: replace ic eeprom


Devices: TV
Brand: Panasonic
Model: tc-20s11j
Symptoms: Tv can not be on and only the sound of ceklak-ceklik.
Cause: Diodes hand over to elco 100/160 volts in a state short.
Solution: Replace the diode with diode 3 Amper, select diode having breakdown voltage above 600 volts.
Note: Diodes are short cause can not terisinya elco 100/160 volts, so it can not be on tv.



Devices: TV
Brand: Panasonic
Model: NICAM STEREO
Symptoms: TV turn itself off about 1-2 minutes, the indicator light also die.
Cause: elko 100v10uf pda pwr suply dry, on its physical look is bloated.
Solution: I changed elko, the TV returns to normal.


Devices: TV
Brand: Panasonic
Model: TC-SERIES GOLDSOUND
Symptom: Horizontal VERTICAL LINE DRAWING ONLY IF CONDITION LIGHT / NORMAL.TAPI BRIGHT IN NORMAL CONDITIONS IF Dim.
Cause: R SHORT
Solution: REPLACE R 525: 120K / 470K



Devices: TV
Brand: Panasonic
Model: alfa gold
Symptoms: often moving picture moving
Cause: tuner
Solution: Initially I did re-solder the tuner section remains the same tp continue sy try to replace the new tuner alhamdulillah jrengg pictures ok ...


Devices: TV
Brand: Panasonic
Model: tc 2088
Symptoms: There is sound no picture, after baeberapa hour on the picture will appear
Cause: There protectionism on video The set, which caused damage to the protectionism in the vertical block
Solution: Try replacing the vertical IC, if still protectionist Change elco transistor on the basis that if Karing proteknya 100/50V it will always protectionism in video sequences.
Note: the requirement on the regulator output voltage under normal circumstances.
Links to this post
Issue 22
Devices: TV
Brand: LG
Model: LG RD-21FB70V
Symptoms: Standby Off
Cause: D23 SHORT
Solution: replace the D23 IN4148


Tools: Monitor
Brand: LG
Model: ld12345
Symptoms: sometimes start sometimes not
Cause: 5 volts output from the regulator drop
Solution: measure and replace elko 100uf/50v


Devices: TV
Brand: LG
Model: LG MC 994A
Symptoms: OFF STANDBY 2
Cause: MOISTURE YOKE
Solution: Turn on the TV, CHECK WHETHER THERE Raster? IF DRY YOKE


Devices: TV
Brand: LG
Model: CA 14A65S
Symptoms: TELEVISION OFF STANDBY 1
Cause: BROKEN VERTICAL IC, IC solder PICTURE IMPERFECT (DROP)
Solution: check the block vertical, vertical ic, if the blue screen check solder IC 1328 TB


Devices: TV
Brand: LG
Model: 14 Inc
Symptoms: TV off standby just normal life can start again
Cause: TEG high electrolyte condensator some not wrong
Solution: replace the electrolytes that damaged condensator



Tools: Monitor
Brand: LG
Model: T530 T710 T730
Symptom: Blinking (led kedip2) button on / off ga maen.
Cause: data eeprom ad that corupted.
Solution: replace and copy eeprom or try overwrhite first.

Tools: Monitor
Brand: LG
Model: T530 T710 T730
Symptoms: FBT dark work but no display, screen raised no ad changes
Cause: cap. filter screen. the block matrix
Solution: replace the cap. trsb or removable aj.


Tools: Monitor
Brand: LG
Model: T710 T730 Flatron
Symptoms: Raster not fully horizontal (right side / left irregular stripes)
Cause: colektor Hrz-capacitor between gnd fire.
Solution: replace the cap. 101/2kv



Tools: Monitor
Brand: LG
Model: T730 T710 Flatron
Symptoms: When the contras Britnes dimaximalkan, kedip2 screen.
Cause: SMPS ic resistor out in 3842 ..
Solution: replace the value above 200 ohm resistor


Devices: TV
Brand: LG
Model: LG 21fu1RL
Symptom: enlarged image to shrink as the light-dark image
Cause: near flyback capacitor 27 nano
Solution: replace with same value
Note: if there is no resale value capacitor replace with a rather large bit could be, or could be a little smaller



Devices: TV
Brand: LG
Model: 20a95
Symptoms: dead alive
Cause: over voltage power
Solution: santi all resistor power supply because nilanya delay all
Note: if you still blink switch elko main
Links to this post
Issue 21
Devices: TV
Brand: Goldstar
Model: CA-14A62
Symptoms: horizontal line
Cause: Tr horizontal broken
Solution: replace with a new horizontal Tr


Devices: TV
Brand: Goldstar
Model: 14xxx
Symptoms: right and left less full picture
Cause: pin flyback voltage less bostup
Solution: elco 220/50v damaged near fb (pin boostup)


Devices: TV
Brand: Goldstar
Model: CA-14A62
Symptoms: Can not find broadcast
Cause: c if angus
Solution: replace the c if used 63pf trimmed slightly


Devices: TV
Brand: Goldstar
Model: 14xxx
Symptoms: right and left less full picture
Cause: pin flyback voltage less bostup
Solution: elco 220/50v damaged near fb (pin boostup)



Devices: TV
Brand: Goldstar
Model: max sound
Symptoms: color to black and white
Cause: lightning
Solution: njek taoh
Note: Soder smua circuit section


Devices: TV
Brand: Goldstar
Model: HCV-502M
Symptoms: Dead total
Cause: R 807 Scorched Regulator section of fire
Solution: Replace R807 with 5K6 value 2watt
Note: Actually his tv brand Nyundai, since in smoke, and rangkaianya like Goldstar / akari


Devices: TV
Brand: Goldstar
Model: 14-inch
Symptoms: TOTAL OFF
Cause: PLY BACK BROKEN
Solution: PLY CHANGE BACK


Devices: TV
Brand: Goldstar
Model: CA 14a64
Symptoms: Total death emerged sounds ngiuuuiik
Cause: Horizontal Tr broken
Solution: replace TR with a new horizontal
Note: after the replacement tr sure hetsink properly attached


Devices: TV
Brand: Goldstar
Model: CA 20 B 32
Symptoms: on for five minutes then return stanby
Cause: elco at the foot of one of the main transformer dry quasi horizontal oscillator
Solution: replace it with a new elko
Note: before performing further checks would be nice all the solder on the horizontal reorganized
Links to this post
Issue 20
Devices: VCD
Brand: China Brand
Model: all models
Symptoms: all keypad not work, the remote control can only be
Cause: infra red led on the internal panel drop
Solution: to vcd, internal panel button turns out to be a remote control, too, so if the panel does not work, and the remote can still be used
Note: make sure switchnyamaka what if that switch is not broken, it can be sure that breaking infrared LED, usually located with the sensor receiver berdekan




Devices: TV
Brand: China Brand
Models: forget the model
Symptoms: tv will not start despite all the normal stress
Cause: kuwalitas flayback are down
Solution: flay back that as a producer of extra high voltage, so the effect was already declining when kuwalitas, aka do not want to spend a high voltage, jd if such reimbursement shall be done
Note: B + TEG usually reduced, but not konseleting, and FBT could only work if the no-load




Devices: TV
Brand: China Brand
Model: 14'' Lost its brand
Symptoms: The OSD does not appear
Cause: afc voltage drop
Solution: increased voltage
Note: Voltage Afc out FBT increased voltage drop! rev ridden by difbt connect to the same FBT out afc afc




Devices: TV
Brand: China Brand
Model: Multimax 14
Symptoms: Matot
Cause: Plyback leak
Solution: Instead of plyback 25-1003B patched mending Gati use 154-177B Rp 27,500 modip tokcer bit, satisfying.





Devices: DVD
Brand: China Brand
Model: EV-333 EDIKO
Symptoms: o ¬ Auda there but there is no picture vidio
Cause: Tr S8550 for vidio output shorting slong
Solution: Replace with new-S8550 tr sure jleng
Note: Related Searches otput Dvd that there is never an biasa.y vido.y trjdi krusakan Tr pda or IC



Devices: VCD
Brand: China Brand
Model: Not ADA
Symptom: No bisaRemote
Cause: The sensor receiver
Solution: Replace the Sensor





Devices: TV
Brand: China Brand
Model: Micom LC863532C
Symptoms: The red color in shadow
Cause: The settings in the R-DRV Sermod maximum due to memory corruption
Solution: Replace the memory IC then setting R-DRV to setandar,
Note: Code Vol srvice 0 Click 6568




Devices: Satellite
Brand: China Brand
Model: MT-88 Mitochiba
Symptoms: Request a password code
Cause: The menu is locked
Solution: Enter the unlock code 8888 Or 0000
Note: If the menu resiver tdak dpat d bka open kde with code 0000 is 8888 resiver





Devices: Satellite
Brand: China Brand
Model: Whole Model
Symptoms: Impressions tv pda resiver no
Cause: Frequesi has changed or resiever re ¬ pabrà program pda or deleted freq jga
Solution: Check the freq frequencies ap msh old or have the new ..
Note: For setting 2 LNB / 4 LNB notice setinganya
Links to this post
Issue 19
Devices: TV
Brand: Toshiba
Model: 21V27DE
Symptoms: total dead
Cause: IC vertical broken / split
Solution: Replace the vertical ic




Devices: TV
Brand: Toshiba
Model: all models
Symptoms: just turned on tv picture fade / blawurjowo bbrapa account after normal hours
Cause: rust on crt focus
Solution: replace the connector pin to focus on clean crt tube crt



Devices: TV
Brand: Toshiba
Model: 21N3XE
Symptoms: Star start small voice, 5 mnit kemudia there and bumpy
Cause: C 308 (35/100) dried
Solution: remove and replace the C 308 (35/100)




Devices: TV
Brand: Toshiba
Model: 21V2VM
Symptoms: if the tv is turned on you hear a "ctas, ctas" like small firecrackers, and direct tv standby
Cause: I try to remove fbtnya, and tv in on it, and I press the + ch, aka normal standbyny lights lit up like a normal tv, tegny good, but if FBT in pairs so its voltage drop,
Solution: its central anode wires apparently leaked, and ic AN5221 SHORT
Note: FBT anode cable leak turned out to be in patches with iron glue (glue 2 tubes, black and white)




Devices: TV
Brand: Toshiba
Model: 21 inches bomba
Symptoms: gmbr normal.suara kddang there, kdang cut no.
Cause: cracked solder
Solution: re-solder solder that looks retea, trutama voting block





Devices: TV
Brand: Toshiba
Model: FLAT ORDINARY
Symptoms: RELAY ON PRINT CETEK.TDK BS
Cause: Protek VCC VERTICAL Drof
Solution: R FUSE VCC VERTKL GNT BROKE NEW




Devices: TV
Brand: Toshiba
Model: 1450XNE
Symptom: Pump Up Regulator (No Load)
Cause: Pump Up Regulator (No Load)
Solution: Check D872 (Zener 16v) ​​on the Regulator.




Devices: TV
Brand: Toshiba
Model: tb1231 use
Symptoms: led blink blink
Cause: elko 25v1oouf create vcc voltage rectifier audio amp dah start soak
Solution: replace ya dong, elko elko tsb.arna also supply 5v tg




Devices: TV
Brand: Toshiba
Model: BOMBA
Symptoms: Whole VOLTAGE REGULATOR OF Drof
Cause: IC VOLTAGE SENSOR BROKEN
Solution: REPLACE IC S1854
Note: IC USED IN THIS COMMON BRAND Whole TOSHIBA




Devices: TV
Brand: Toshiba
Model: V29 DRAMATIC NICAM
Symptoms: IMAGES ILANG2
Cause: MVCS MODULE 43D VIF & AFTNYA BROKEN
Solution: CHANGE C AFT T104 C56PF.VIF to3 12PF




Devices: TV
Brand: Toshiba
Model: 21lze28
Symptoms: button / switch front panel for channel and volume does not work, the remote does not work
Cause: frontpanel switches in the circuit, there is a 100nF ceramic capacitor (leaked) short to ground
Solution: Remove and Replace a 100nF ceramic capacitor with a new




Devices: TV
Brand: Toshiba
Model: 21 Inch
Symptoms: stand by
Cause: high voltage fuse 1.5 A drop
Solution: replace the fuse and that bloated elco





Devices: TV
Brand: Toshiba
Model: 29A3E
Symptoms: amid undulating image horizontally and there is a straight line in the horizontal
Cause: deflection coil / yoke short vertical section
Solution: replace the yoke horse's mouth.
Links to this post
Issue 18
Devices: TV
Brand: Sony
Model: kv 2965
Symptom: No sound ringing off tv
Cause: tr hor out dead / short
Solution: replace c 47mF/50v & c10mF/100v in power diode suply.ganti R2KY, check tegngan B + 135v.ganti c1mF/250v in horizontal, tr hor out 4927. ready dionkan ..
Note: tr 4927 short caused b + voltage over


Devices: TV
Brand: Sony
Model: KV 614B1
Symptoms: Raster missing
Cause: Resistor dead
Solution: Change the value of the original 82K R857 near FBT
Note: This Tv Croma use IC TDA8366, STR S6707 and FBT 859-957-00



Devices: TV
Brand: Sony
Model: CXA croma
Symptoms: dark dim g crt sprt nrmal
Cause: abl g nrmal
Solution: co-abl pathways mnju k tr ad chroma paste biasax dead soth Gant / lpas j trx


Devices: TV
Brand: Sony
Model: kv G14P1
Symptoms: live tv, sound normal, normal OSD, no picture
Cause: ABL resistor open (dilate value)
Solution: replace the ABL resistor, R 319


Devices: TV
Brand: Sony
Model: KV21M9
Symptom: Picture megecil center of the screen
Cause: SMPS circuit problem
Solution: Replace IC STR
Note: be careful live chassis.


Devices: TV
Brand: Sony
Model: KP-FX43M61
Symptoms: IMAGE PROBLEM, pulsating COLOR INPUT ANT / AV
Cause: since moved locations a TV, and a great shock, sometimes the memory image to reset
Solution: adjust the data OPM-COM in service mode


Devices: TV
Brand: Sony
Model: KV-HF21P50
Symptom: DARK PICTURE
Cause: ABL PROBLEM IF
Solution: REPLACE Q312 (2SA1162-G) AND D315 (ISS355)



Devices: TV
Brand: Sony
Model: KV-PG14
Symptoms: PROTECT blink 4X
Cause: vertical problem
Solution: the transistor chip breaking Q005


Devices: TV
Brand: Sony
Model: KV-M1420A
Symptoms: There is a picture but no sound
Cause: Damage to the sound amplifier
Solution: Replace IC201 TDA7345


Devices: TV
Brand: Sony
Model: kv-2965
Symptoms: images shrink and concave
Cause: ic damaged OW (TEA2031)
Solution: replace the IC OW and perform geometry image realignment.
Links to this post
17th Edition
Devices: TV
Brand: Sharp
Model: Chassis UA-1
Symptoms: Raster dark, entered service mode ok, exit service mode dark again.
Cause: Data eprom change.
Solution: change the data service mode EVG from 1 to 0 and EHT from 1 to 0
Note: Model Chassis UA-1 universe and wonder


Devices: TV
Brand: Sharp
Model: 51X220 EXPRESSION
Symptoms appear without FIGURE WITH SOUND HIDUP.KADANG POSITION BACK TO STANDBY (Protek)
Cause: Unknown ill
Solution: REPLACE R limiters for 180V R621: 1 OHM


Devices: TV
Brand: Sharp
Model: C14JO
Symptoms: SMALL IMAGES few centimeters amid SAJA.RASTER JUST EMPTY / BINTIK.KESALAHAN HAPPEN TO TRACK 12V
Cause: Unknown ill
Solution: REPLACE Q604 FOR FURTHER D ration 12Volt GET TO TUNER.


Devices: TV
Brand: Sharp
Model: Qbeit 11
Symptoms: There Raster broadcast in smoke
Cause: lightning hit
Solution: lightning hit damage after check everything turns his IC died after learning scheme
Note: for all of what two colleagues when stock runs out the use ic sharp 1XC 927WJZZQ IC IC CHANGE AJ wearing IXC 844WJZZ.selamat try


Devices: TV
Brand: Sharp
Model: piccolo
Symptoms: totally dead
Cause: The death total
Solution: First check for str replace regulator outputnya.terus setandar.jika voltage problem lamp flame stnby can not check ic program.
Note: if ic program (R2J1Q172GA-A00FP) do not try to use ic flame. {1X245 WJN] jadi.ta Thank God there is a problem.


Devices: TV
Brand: Sharp
Model: Alexander 21inch
Symptoms: Indicators sbntar truz flame die. . .
Cause: Protek Regulator
Solution: Replace fet SE 125


Devices: TV
Brand: Sharp
Model: X-pression 51X200
Symptoms: Normal Voice, Picture can not FOCUS
Causes: Leg focus on crt half short.
Solution: The image can not focus not from the flyback or the socket and glue gagal.plastik crt that was already cleared of foot crt, focus mainly on the feet.
Note: After being tested to other crt, good picture quality is perfect! Crt dng such cases the damage as if from its flyback fail. ooh .. sharp


Devices: TV
Brand: Sharp
Model: 51X200 Xpression
Symptoms: Image v hold / cliche
Cause: C 434 measured 3.3 uF 10/50V err
Solution: Replace with a good


Devices: TV
Brand: Sharp
Model: fdfde
Symptoms: totally dead
Cause: short horizontal transistors
Solution: Change Transistor
Links to this post
Issue 16
Devices: TV
Brand: Sanyo
Model: dyamic
Symptoms: life briefly and protectionism
Cause: his unusual happened so changes in the HFC horisontal.abl or heater that resulted in the protectionist
Solution: cut line by clicking protectionism is looking for a value r his 1k that kejalur protectionism of ic program tv Insa Allah normal




Devices: TV
Brand: Sanyo
Model: cg21fs2
Symptoms: normal images. lost voice
Cause: ic switching av 1116 N LV series is broken.
Solution: replace the normal N.tv LV 1116.
Note: AV out when plugged into the tv sound amplifier can walk.




Devices: TV
Brand: Sanyo
Model: CAP3002
Symptoms: MATI.DENGAN TR.HOR SHORT CONDITION. TR.REG REPLACED WHEN HIS, VOLTAGE UP TO 200V B + risen MORE
Cause: DAMAGE TO SECTION R555 optocoupler 47KOHM
Solution: replace the 47k ohm r555




Devices: TV
Brand: Sanyo
Model: cgs21fs
Symptoms: protect
Cause: flayback bocot
Solution: replace flayback




Devices: TV
Brand: Sanyo
Model: 14 inch
Symptoms: dying with perforated horizontal transistor
Cause: breaking r47k part ic opto
Solution: replace r47k
Note: also check ic opto



Devices: TV
Brand: Sanyo
Model: model forget
Symptoms: tv when turned glowing red indicator blink blink wrote ter aka protectionism
Cause: apparently after dilhat ditelusurri kissed and touched only on the location of the damage to flyback terprotek
Solution: replace the flyback solosinya yes definitely jos




Devices: TV
Brand: Sanyo
Model: CG 21 XS 2
Symptoms: TV stand is locked in position by.kalau power in on.TV willing to live and die lagi.protec
Cause: eeprom if its OK, then the vertical IC OK.B + 5 volt OK.
Solution: J830 jemper off, or change it directly FBT.
Note: tgl.27 september 2010




Devices: TV
Brand: Sanyo
Model: Dinamic
Symptoms: Dead total
Cause: Power Transistor suply shot
Solution: Replace the transistor
Note: Change the type of bu. . .




Devices: TV
Brand: Sanyo
Model: N0 chassis AC6A1
Symptom: No sound volume max sdh, Nice pictures
Cause: IC 3701 LV1116 broken
Solution: Before replacing the ic try this alternative way, off his first ic, wash the feet of his lower leg ic wear cuter / fine sandpaper, then reinstall nya.kl ic voice ic still not out Change lv1116N,
Note: kl spertpat interchangeable hard in his search to SC, Bs jg look at his blog mas alextro service, http://alextro-service.blogspot.com/




Devices: TV
Brand: Sanyo
Model: CG14SP1N
Symptoms: Dead total
Cause: TR Horz koslet (B & E)
Solution: replace TR Horz




Devices: TV
Brand: Sanyo
Model: FLAT SLIM CG21XS2 21
Symptoms: VOTE nonexistent
Cause: MEMORY NOT WORK NORMALLY WHEN DATA settings OK
Solution: The data SETTING FIRST, CAN NEW NGK KLO GNTI IC MEMORY
Note: SANYO MODEL UMTK NATURAL SY OFTEN DAMAGED DATA / IC MEMORY




Devices: TV
Brand: Sanyo
Model: CG21XS2
Symptoms: always return to standby will continue when lit
Cause: flyback his tiny little problem .. internal capacitor capacity changes FBT
Solution: with a way to cut (break) .. J830 jumper that led pin 23 of IC LA76938 (pin is called: INT1/P.0) one pin to detect / control the horizontal section.
Links to this post
Issue 15
Devices: TV
Brand: Samsung
Model: CS-29M21MQUXXSE
Symptoms: Blanking
Cause: Micon on ngepong,
Solution: Solder again.!



Devices: TV
Brand: Samsung
Model: flat 17inci
Symptoms: horizontal off continues
Cause: yoke konslet
Solutions: email lifting ll wipe lg dg dg thiner glue alteco 1/1
Note: buy overpriced yoke again



Devices: VCD
Brand: Samsung
Model: Z10Q
Symptom: No picture
Cause: Video output from puts zic3
Solution: Merge / jumper pin 13 with pin 4 zic3
Note: Can jga len dpts and pindahkn pin 13 directly to pin 4 on zic3 (Winbond W99520P)



Devices: TV
Brand: Samsung
Model: 21 flat
Symptoms: The first normal picture, about two minutes blanking green,
Cause: RGB bag there is an abnormal voltage
Solution: tr bersihin RGB in, if there is to be replaced,,,,


Devices: TV
Brand: Samsung
Model: TDA 9381 series
Symptoms: thin raster image darker
Cause: capacitor abl colector tr haritdk work or SSR
Solution: replace with a new one according to the original value capacitor voltage in the semestina have 2 to 4.5 volts
Note: common on Samsung in the generation above and the Visian zoom silver color body



Devices: TV
Brand: Samsung
Model: Slim fit
Symptoms: SAMSUNG 21Z40 Dead Total
Cause: no voltage on Output Transformer Switching off the TV so that the total
Solution: for TV models is mostly the damage was caused by the rupture resistor between the AC voltage source with a diode rectifier to supply IC STR W6750.




Devices: TV
Brand: Samsung
Model: CB-3338Z
Symptoms: Dead, flyback sound.
Cause: faulty horizontal transistor (short col-emi)
Solution: replace the transistor hor D2125 with that original, do not replace with any trans hor as it might seem the picture slide to the left and did not last long.




Devices: TV
Brand: Samsung
Model: Flat_
Symptoms: Channel Move-move themselves
Cause: zener diode on pin Shortnya key input
Solution: replace the value of the zener diode 3.6 V
Note: 14-inch Samsung flat, single chip TDA 9381 PS

1 comments:

Unknown said...

sharp 14w25 schematic diagram wanted

Post a Comment

◄ Posting Baru Posting Lama ►
 

Followers

Total Pageviews

Copyright © 2012. Studied Business Computer Electronics - All Rights Reserved B-Seo Versi 5 by Bamz